资料下载
×
AD8129/AD8130 pdf datasheet (D
消耗积分:5 |
格式:rar |
大小:555 |
2008-08-06
刘杰
分享资料个
The AD8129 and AD8130 are designed as receivers for the
transmission of high-speed signals over twisted-pair cables to
work with the AD8131 or AD8132 drivers. Either can be
used for analog or digital video signals and for high-speed
data transmission. The AD8129 and AD8130 are differentialto-
single-ended amplifiers with extremely high CMRR at high
frequency. Therefore, they can also be effectively used as
high-speed instrumentation amps or for converting differential
signals to single-ended signals.
The AD8129 is a low-noise high-gain (10 or greater) version
intended for applications over very long cables where signal
attenuation is significant. The AD8130 is stable at a gain of one
and can be used for those applications where lower gains are
required. Both have user adjustable gain to help compensate for
losses in the transmission line. The gain is set by the ratio of
two resistor values. The AD8129 and AD8130 have very high
input impedance on both inputs regardless of the gain setting.
The AD8129 and AD8130 have excellent common-mode rejection
(70 dB @ 10 MHz) allowing the use of low cost unshielded
twisted-pair cables without fear of corruption by external noise
sources or crosstalk.
The AD8129 and AD8130 have a wide power supply range
from single 5 V supply to ±12 V, allowing wide common-mode
and differential-mode voltage ranges while maintaining signal
integrity. The wide common-mode voltage range will enable
the driver receiver pair to operate without isolation transformers
in many systems where the ground potential difference
between drive and receive locations is many volts. The AD8129
and AD8130 have considerable cost and performance improvements
over op amps and other multi-amplifier receiving solutions.
transmission of high-speed signals over twisted-pair cables to
work with the AD8131 or AD8132 drivers. Either can be
used for analog or digital video signals and for high-speed
data transmission. The AD8129 and AD8130 are differentialto-
single-ended amplifiers with extremely high CMRR at high
frequency. Therefore, they can also be effectively used as
high-speed instrumentation amps or for converting differential
signals to single-ended signals.
The AD8129 is a low-noise high-gain (10 or greater) version
intended for applications over very long cables where signal
attenuation is significant. The AD8130 is stable at a gain of one
and can be used for those applications where lower gains are
required. Both have user adjustable gain to help compensate for
losses in the transmission line. The gain is set by the ratio of
two resistor values. The AD8129 and AD8130 have very high
input impedance on both inputs regardless of the gain setting.
The AD8129 and AD8130 have excellent common-mode rejection
(70 dB @ 10 MHz) allowing the use of low cost unshielded
twisted-pair cables without fear of corruption by external noise
sources or crosstalk.
The AD8129 and AD8130 have a wide power supply range
from single 5 V supply to ±12 V, allowing wide common-mode
and differential-mode voltage ranges while maintaining signal
integrity. The wide common-mode voltage range will enable
the driver receiver pair to operate without isolation transformers
in many systems where the ground potential difference
between drive and receive locations is many volts. The AD8129
and AD8130 have considerable cost and performance improvements
over op amps and other multi-amplifier receiving solutions.
声明：本文内容及配图由入驻作者撰写或者入驻合作网站授权转载。文章观点仅代表作者本人，不代表电子发烧友网立场。文章及其配图仅供工程师学习之用，如有内容侵权或者其他违规问题，请联系本站处理。 举报投诉
评论(0)
发评论
- 相关下载
- 相关文章
