stm32f103c8t6串口3能用吗

void USART3_Initialise( u32 bound )
{
    GPIO_InitTypeDef GPIO_InitStructure;
    NVIC_InitTypeDef NVIC_InitStructure;
    USART_InitTypeDef USART_InitStructure;

  /* Enable the USART3 Pins Software Remapping */
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB| RCC_APB2Periph_AFIO ,ENABLE);
          GPIO_PinRemapConfig(GPIO_FullRemap_USART3, ENABLE);
    RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART3, ENABLE);


/* Configure USART3 Rx (PB.11) as input floating */
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_11;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_Init(GPIOB, &GPIO_InitStructure);

/* Configure USART3 Tx (PB.10) as alternate function push-pull */
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_Init(GPIOB, &GPIO_InitStructure);

/* Enable the USART3 Interrupt */
NVIC_PriorityGroupConfig(NVIC_PriorityGroup_3);
NVIC_InitStructure.NVIC_IRQChannel = USART3_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 1;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);

USART_InitStructure.USART_BaudRate = bound;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;       

USART_Init(USART3, &USART_InitStructure);
USART_ITConfig(USART3, USART_IT_RXNE, ENABLE);


USART_Cmd(USART3, ENABLE);
USART_ClearFlag(USART3, USART_FLAG_TXE);
}

// USART3DATA[20]=0;
        void USART3_IRQHandler(void)                             //´®¿ÚÖжÏÊäÈë
{
        static u8 i = 0;
        u8 data = 0;
      if(USART_GetFlagStatus(USART3, USART_FLAG_RXNE) == SET)
      {
       data = USART_ReceiveData(USART3);
                                //i++;
                                //if(i == 9)
                                 //{
                                        //i = 0;
                                        //temp1 = 1;                                       
         
       // }
        USART_SendData(USART3, data);
                         }
}

  GPIO_InitTypeDef GPIO_InitStructure;
    NVIC_InitTypeDef NVIC_InitStructure;
    USART_InitTypeDef USART_InitStructure;

  /* Enable the USART3 Pins Software Remapping */
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB| RCC_APB2Periph_AFIO ,ENABLE);
          GPIO_PinRemapConfig(GPIO_FullRemap_USART3, ENABLE);
    RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART3, ENABLE);

告诉你，能用。以前用过。

万恶的，你你确定以前你用的是STM32F103C8T6，亲测不行，STM32F103ZET6 可以用。复用映射的

c8t6是可以映射的

c8t6的串口3好像只能发送，不能接受