创客神器NanoPi
直播中

DXK123~

9年用户 85经验值
擅长:嵌入式技术 控制/MCU
私信 关注
[问答]

【NanoPi M2试用体验】进不去系统求助

` 本帖最后由 DXK123~ 于 2016-5-22 10:14 编辑


    话说离写上一篇帖子已经很长的时间了，由于最近学校组织参加了全国机械大赛，我作为控制系统的的开发人员，也跟上打了几天酱油，所以很久没有发帖了，还希望大家多多包涵，上次说了，神器的确是很棒的，上网放视频都没有卡顿，比起曾经玩过野火的板子，那直接可以说是天上地下吧。
回来后，直接奔着板子就准备好好玩一下，习惯的上电后，但是这次却没有正常启动，我也不知道怎么回事，现在把从串口打印出的信息贴出来，让大神瞧瞧，到底是怎么回事了，我已经折腾了一天半了，实在无能为力了。这是烧安卓后的界面，一直显示这样。
串口打印的信息
  1. -------------------------------------------------------------------------------
  2. Second Boot by Nexell Co. : Ver0.6.1 - Built on Oct 16 2015 13:42:17
  3. --------------------------------------------------------------------------------
  4. EMA VALUE : 001
  5. 123
  6. Lock value  = 157
  7. GATE CYC    = 0x00008421
  8. GATE CODE   = 0x3A3A3A3A
  9. Read  DQ    = 0x08080808
  10. Write DQ    = 0x08080808
  11. Loading from sdmmc...
  12. Image Loading Done!
  13. Launch to 0x42C00000


  16. U-Boot 2014.07-gb44132b (Jan 19 2016 - 17:35:14)

  18. PLL : [0] =  550000000, [1] =  800000000, [2] =  800000000, [3] =  614399000
  19. PLL1: CPU FCLK =  800000000, HCLK = 200000000
  20. PLL2: BUS BCLK =  400000000, PCLK = 200000000
  21. PLL2: MEM MCLK =  800000000, DCLK = 800000000, BCLK = 400000000, PCLK = 200000000
  22. PLL0: G3D BCLK =  550000000
  23. PLL2: MPG BCLK =  400000000, PCLK = 200000000
  24. I2C:   ready
  25. DRAM:  256 MiB
  26. Heap = 0x43000000~0x45000000
  27. Code = 0x42c00000~0x42c73984
  28. GLD  = 0x42bffeb8
  29. GLBD = 0x42bffe68
  30. SP   = 0x42bffe68,0x42bffe50(CURR)
  31. PC   = 0x42c06114
  32. TAGS = 0x40000100
  33. PAGE = 0x42c80000~0x42c8c000
  34. MACH = [4330]   
  35. VER  = 1      
  36. BOARD= [nanopi2]   
  37. LCD  = X710
  38. MMC:   NXP DWMMC: 0, NXP DWMMC: 1, NXP DWMMC: 2
  39. In:    serial
  40. Out:   serial
  41. Err:   serial
  42. switch to partitions #0, OK
  43. mmc0 is current device
  44. RGB: display.0
  45. DISP: W=1024, H= 600, Bpp=32
  46. DONE: Logo bmp 800 by 480 (3bpp), len=1152056
  47. DRAW: 0x47000000 -> 0x46000000
  48. Hit any key to stop autoboot:  0
  49. ## Booting kernel from Legacy Image at 48000000 ...
  50.    Image Name:   Linux-3.4.39-s5p4418
  51.    Image Type:   ARM Linux Kernel Image (uncompressed)
  52.    Data Size:    4392288 Bytes = 4.2 MiB
  53.    Load Address: 40008000
  54.    Entry Point:  40008000
  55.    Verifying Checksum ... OK
  56.    Loading Kernel Image ... OK

  58. Starting kernel ...

  60. [    0.000000] Booting Linux on physical CPU 0
  61. [    0.000000] Initializing cgroup subsys cpuset
  62. [    0.000000] Initializing cgroup subsys cpu
  63. [    0.000000] Linux version 3.4.39-s5p4418 (root@jensen) (gcc version 4.9.3 (ctng-1.21.0-229g-FA) ) #104 SMP PREEMPT Fri Apr 15 16:54:19 HKT 2016
  64. [    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
  65. [    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
  66. [    0.000000] Machine: NANOPI2
  67. [    0.000000] Display: X710 selected
  68. [    0.000000] nxp_reserve_mem: reserve CMA: size 201326592
  69. [    0.000000] NXP/CMA: Reserved 0x63600000/0x0c000000 for 'ion'
  70. [    0.000000] NXP/CMA: success register cma region for 'ion'
  71. [    0.000000] Memory policy: ECC disabled, Data cache writealloc
  72. [    0.000000] CPU : iomap[ 0]: p 0xc0000000 -> v 0xf0000000 len=0x300000
  73. [    0.000000] CPU : iomap[ 1]: p 0xf0000000 -> v 0xf0300000 len=0x100000
  74. [    0.000000] CPU : iomap[ 2]: p 0xcf000000 -> v 0xf0400000 len=0x100000
  75. [    0.000000] CPU : iomap[ 3]: p 0x2c000000 -> v 0xf0500000 len=0x100000
  76. [    0.000000] CPU : iomap[ 4]: p 0x00000000 -> v 0xf0600000 len=0x100000
  77. [    0.000000] CPU : DMA Zone Size =16M, CORE 4
  78. [    0.000000] CPU : VERSION = 2 (0xE153000A), Assign Peripheral Exclusive Bus
  79. [    0.000000] s5p4418-NanoPi2: Board initialized
  80. [    0.000000] CPU : Clock Generator= 64 EA, DVFS = support, PLL.1
  81. [    0.000000] PLL : [0] =  550000000, [1] =  800000000, [2] =  800000000, [3] =  614399000
  82. [    0.000000] PLL1: CPU FCLK =  800000000, HCLK = 200000000
  83. [    0.000000] PLL2: BUS BCLK =  400000000, PCLK = 200000000
  84. [    0.000000] PLL2: MEM MCLK =  800000000, DCLK = 800000000, BCLK = 400000000, PCLK = 200000000
  85. [    0.000000] PLL0: G3D BCLK =  550000000
  86. [    0.000000] PLL2: MPG BCLK =  400000000, PCLK = 200000000
  87. [    0.000000] PERCPU: Embedded 9 pages/cpu @c127f000 s12352 r8192 d16320 u36864
  88. [    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 259839
  89. [    0.000000] Kernel command line: console=ttyAMA0,115200n8 root=/dev/mmcblk0p2 rootfstype=ext4 rootwait init=/***in/init systemd.show_status=false g_ether.host_addr=82:cf:ce:fa:44:18 initrd=0x49000000,0x400000 console=tty1 lcd=X710
  90. [    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
  91. [    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
  92. [    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
  93. [    0.000000] allocated 2097152 bytes of page_cgroup
  94. [    0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
  95. [    0.000000] Memory: 1024MB = 1024MB total
  96. [    0.000000] Memory: 825932k/825932k available, 222644k reserved, 272384K highmem
  97. [    0.000000] Virtual kernel memory layout:
  98. [    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
  99. [    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
  100. [    0.000000]     vmalloc : 0xef800000 - 0xfee00000   ( 246 MB)
  101. [    0.000000]     lowmem  : 0xc0000000 - 0xef600000   ( 758 MB)
  102. [    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
  103. [    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
  104. [    0.000000]       .text : 0xc0008000 - 0xc07e2fec   (8044 kB)
  105. [    0.000000]       .init : 0xc07e3000 - 0xc081a040   ( 221 kB)
  106. [    0.000000]       .data : 0xc081c000 - 0xc089a600   ( 506 kB)
  107. [    0.000000]        .bss : 0xc089a624 - 0xc0975498   ( 876 kB)
  108. [    0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
  109. [    0.000000] Preemptible hierarchical RCU implementation.
  110. [    0.000000] NR_IRQS:288
  111. [    0.000000] VIC @f0002000: id 0x00041192, vendor 0x41
  112. [    0.000000] VIC @f0003000: id 0x00041192, vendor 0x41
  113. [    0.000000] GPIO  @f001a000: start  64, mask 0xffffffff (gpio 53)
  114. [    0.000000] GPIO  @f001b000: start  96, mask 0xffffffff (gpio 54)
  115. [    0.000000] GPIO  @f001c000: start 128, mask 0xffffffff (gpio 55)
  116. [    0.000000] GPIO  @f001d000: start 160, mask 0xffffffff (gpio 56)
  117. [    0.000000] GPIO  @f001e000: start 192, mask 0xffffffff (gpio 57)
  118. [    0.000000] ALIVE @f0010800: start 224, mask 0x000000ff (alive 4)
  119. [    0.000000] GIC   @f0301000: start 256 (vic 31)
  120. [    0.000000] timer.0: source,  10000000(HZ:250), mult:3355443200
  121. [    0.000000] timer.1: event ,  10000000(HZ:250), mult:42949673
  122. [    0.000000] sched_clock: 32 bits at 250 Hz, resolution 4000000ns, wraps every 4294967292ms
  123. [    0.000000] Console: colour dummy device 80x30
  124. [    0.000000] console [tty1] enabled
  125. [    0.000000] Calibrating delay loop... 1594.36 BogoMIPS (lpj=3188736)
  126. [    0.048000] pid_max: default: 32768 minimum: 301
  127. [    0.048000] Security Framework initialized
  128. [    0.048000] SELinux:  Initializing.
  129. [    0.048000] Mount-cache hash table entries: 512
  130. [    0.048000] Initializing cgroup subsys cpuacct
  131. [    0.048000] Initializing cgroup subsys memory
  132. [    0.048000] Initializing cgroup subsys devices
  133. [    0.048000] Initializing cgroup subsys freezer
  134. [    0.048000] CPU: Testing write buffer coherency: ok
  135. [    0.048000] CPU0: thread -1, cpu 0, socket 10, mpidr 80000a00
  136. [    0.048000] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
  137. [    0.048000] Setting up static identity map for 0x405df8d0 - 0x405df928
  138. [    0.048000] L310 cache controller enabled
  139. [    0.048000] l2x0: 16 ways, CACHE_ID 0x4100c4c8, AUX_CTRL 0x70470001, Cache size: 1048576 B
  140. [    0.092000] CPU1: thread -1, cpu 1, socket 10, mpidr 80000a01
  141. [    0.132000] CPU2: thread -1, cpu 2, socket 10, mpidr 80000a02
  142. [    0.172000] CPU3: thread -1, cpu 3, socket 10, mpidr 80000a03
  143. [    0.176000] Brought up 4 CPUs
  144. [    0.176000] SMP: Total of 4 processors activated (6377.47 BogoMIPS).
  145. [    0.176000] devtmpfs: initialized
  146. [    0.180000] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
  147. [    0.184000] pwm: max = 50000000 hz
  148. [    0.184000] prepare_gpio_suspend:
  149. [    0.184000]   alfn[0][0]: 0x00000000, alfn[0][1]: 0x00000000
  150. [    0.184000]   alfn[1][0]: 0x66800000, alfn[1][1]: 0x55555566
  151. [    0.184000]   alfn[2][0]: 0x55555555, alfn[2][1]: 0x00555555
  152. [    0.184000]   alfn[3][0]: 0x00000000, alfn[3][1]: 0x00000000
  153. [    0.184000]   alfn[4][0]: 0x00000000, alfn[4][1]: 0x55540000
  154. [    0.184000] dummy:
  155. [    0.184000] NET: Registered protocol family 16
  156. [    0.184000] [Register machine platform devices]
  157. [    0.184000] mach: add amba device uart-pl011.0
  158. [    0.184000] mach: add amba device uart-pl011.1
  159. [    0.184000] mach: add amba device uart-pl011.3
  160. [    0.184000] mach: add amba device uart-pl011.4
  161. [    0.184000] mach: add amba device pl08xdmac.0
  162. [    0.184000] mach: add amba device pl08xdmac.1
  163. [    0.184000] mach: add amba device ssp-pl022.0
  164. [    0.188000] mach: add device syncgen [2]
  165. [    0.188000] mach: add device lcd
  166. [    0.188000] mach: add device i2c bus (array:3)
  167. [    0.188000] mach: add device Real Time Clock  
  168. [    0.188000] mach: add device generic pwm (array:4)
  169. [    0.188000] mach: add device generic gpio (array:6)
  170. [    0.188000] mach: add device i2s (array:1)
  171. [    0.188000] mach: add device spdif tx
  172. [    0.188000] mach: add device u***_ehci
  173. [    0.188000] mach: add device u***_ohci
  174. [    0.188000] mach: add device u*** otg
  175. [    0.188000] mach: add device ion-nxp
  176. [    0.188000] mach: add device adc
  177. [    0.188000] mach: add graphic device opengl|es
  178. [    0.188000] [Register board platform devices]
  179. [    0.188000] plat: board revision 5
  180. [    0.188000] plat: add dynamic frequency (pll.1)
  181. [    0.188000] plat: add device adc temp
  182. [    0.188000] plat: add framebuffer
  183. [    0.188000] plat: boot from mmc.0
  184. [    0.188000] plat: add device sdmmc [0]
  185. [    0.192000] plat: add backlight pwm device
  186. [    0.192000] plat: add device keypad
  187. [    0.192000] plat: add device spdif playback
  188. [    0.192000] plat: add device asoc-es8316
  189. [    0.192000] plat: add device nxp-v4l2
  190. [    0.192000] plat: register spidev
  191. [    0.192000] plat: add touch(ft5x0x) device
  192. [    0.192000] plat: add touch(it7260) device
  193. [    0.192000] plat: add onewire ts device
  194. [    0.192000] plat: add adxl34x device
  195. [    0.192000] plat: add bmp085 device
  196. [    0.192000] plat: add ds1307 device
  197. [    0.192000] plat: add pcf8591 device
  198. [    0.192000] plat: add device nxp-gmac
  199. [    0.196000] plat: add device gpio_led
  200. [    0.196000] plat: add device pwm_led
  201. [    0.196000]
  202. [    0.196000] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
  203. [    0.196000] hw-breakpoint: maximum watchpoint size is 4 bytes.
  204. [    0.196000] Serial: AMBA PL011 UART driver
  205. [    0.196000] uart-pl011.0: ttyAMA0 at MMIO 0xc00a1000 (irq = 7) is a PL011 rev3
  206. [    0.200000] console [ttyAMA0] enabled
  207. [    0.204000] uart-pl011.1: ttyAMA1 at MMIO 0xc00a0000 (irq = 6) is a PL011 rev3
  208. [    0.208000] uart-pl011.3: ttyAMA2 at MMIO 0xc00a3000 (irq = 9) is a PL011 rev3
  209. [    0.212000] uart-pl011.4: ttyAMA3 at MMIO 0xc006d000 (irq = 10) is a PL011 rev3
  210. [    0.236000] bio: create slab at 0
  211. [    0.240000] gpiochip_add: registered GPIOs 0 to 31 on device: nxp-gpio.0
  212. [    0.248000] gpiochip_add: registered GPIOs 32 to 63 on device: nxp-gpio.1
  213. [    0.252000] gpiochip_add: registered GPIOs 64 to 95 on device: nxp-gpio.2
  214. [    0.256000] gpiochip_add: registered GPIOs 96 to 127 on device: nxp-gpio.3
  215. [    0.260000] gpiochip_add: registered GPIOs 128 to 159 on device: nxp-gpio.4
  216. [    0.264000] gpiochip_add: registered GPIOs 160 to 167 on device: nxp-gpio.5
  217. [    0.268000] pl08xdmac pl08xdmac.0: Unbalanced pm_runtime_enable!
  218. [    0.272000] pl08xdmac pl08xdmac.0: initialized 8 virtual memcpy channels
  219. [    0.276000] pl08xdmac pl08xdmac.0: initialized 16 virtual slave channels
  220. [    0.284000] pl08xdmac pl08xdmac.0: DMA: PL080 rev1 at 0xc0000000 irq 1
  221. [    0.288000] pl08xdmac pl08xdmac.1: Unbalanced pm_runtime_enable!
  222. [    0.292000] pl08xdmac pl08xdmac.1: initialized 8 virtual memcpy channels
  223. [    0.296000] pl08xdmac pl08xdmac.1: initialized 15 virtual slave channels
  224. [    0.300000] pl08xdmac pl08xdmac.1: DMA: PL080 rev1 at 0xc0001000 irq 2
  225. [    0.304000] nxp_ion_probe success!!!
  226. [    0.308000] SCSI subsystem initialized
  227. [    0.312000] ssp-pl022 ssp-pl022.0: ARM PL022 driver, device ID: 0x00041022
  228. [    0.316000] pl022: mapped registers from 0xc005b000 to f005b000
  229. [    0.320000] ssp-pl022 ssp-pl022.0: setup for DMA on RX dma1chan7, TX dma1chan6
  230. [    0.324000] ssp-pl022 ssp-pl022.0: will use autosuspend for runtime pm, delay 10ms
  231. [    0.328000] u***core: registered new interface driver u***fs
  232. [    0.332000] u***core: registered new interface driver hub
  233. [    0.336000] u***core: registered new device driver u***
  234. [    0.340000] i2c-gpio i2c-gpio.3: using pins 159 (SDA) and 158 (SCL)
  235. [    0.344000] nxp-i2c.0:   390625 hz [pclk=200000000, clk = 256, scale= 1, timeout= 500 ms]
  236. [    0.348000] nxp-i2c.1:    97656 hz [pclk=200000000, clk = 256, scale= 7, timeout= 500 ms]
  237. [    0.352000] nxp-i2c.2:   195312 hz [pclk=200000000, clk = 256, scale= 3, timeout= 500 ms]
  238. [    0.356000] Linux media interface: v0.10
  239. [    0.360000] Linux video capture interface: v2.00
  240. [    0.364000] pps_core: LinuxPPS API ver. 1 registered
  241. [    0.368000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
  242. [    0.372000] PTP clock support registered
  243. [    0.380000] axp_mfd 3-0034: AXP (CHIP ID: 0x06) detected
  244. [    0.388000] axp22_ldo1: 3000 mV
  245. [    0.396000] axp22_aldo1: 700 <--> 3300 mV at 3300 mV
  246. [    0.404000] axp22_aldo2: 700 <--> 3300 mV at 1800 mV
  247. [    0.412000] axp22_aldo3: 700 <--> 3300 mV at 1000 mV
  248. [    0.420000] axp22_dldo1: 700 <--> 3300 mV at 3300 mV
  249. [    0.428000] axp22_dldo2: No configuration
  250. [    0.432000] axp22_dldo2: 700 <--> 3300 mV at 700 mV
  251. [    0.436000] axp22_dldo3: No configuration
  252. [    0.444000] axp22_dldo3: 700 <--> 3300 mV at 700 mV
  253. [    0.448000] axp22_dldo4: No configuration
  254. [    0.452000] axp22_dldo4: 700 <--> 3300 mV at 700 mV
  255. [    0.460000] axp22_eldo1: 700 <--> 3300 mV at 1800 mV
  256. [    0.468000] axp22_eldo2: 700 <--> 3300 mV at 3300 mV
  257. [    0.476000] axp22_eldo3: No configuration
  258. [    0.480000] axp22_eldo3: 700 <--> 3300 mV at 700 mV
  259. [    0.484000] axp22_dc5ldo: No configuration
  260. [    0.492000] axp22_dc5ldo: 700 <--> 1400 mV at 1200 mV
  261. [    0.500000] axp22_dcdc1: 1600 <--> 3400 mV at 3300 mV
  262. [    0.508000] axp22_dcdc2: 600 <--> 1540 mV at 1200 mV
  263. [    0.516000] axp22_dcdc3: 600 <--> 1860 mV at 1200 mV
  264. [    0.524000] axp22_dcdc4: 600 <--> 1540 mV at 1500 mV
  265. [    0.532000] axp22_dcdc5: 1000 <--> 2550 mV at 1500 mV
  266. [    0.540000] axp22_ldoio0: 700 <--> 3300 mV at 3800 mV
  267. [    0.548000] axp22_ldoio1: 700 <--> 3300 mV at 3800 mV
  268. [    0.552000] Advanced Linux Sound Architecture Driver Version 1.0.25.
  269. [    0.556000] Switching to clocksource source timer
  270. [    0.580000] NET: Registered protocol family 2
  271. [    0.588000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
  272. [    0.596000] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
  273. [    0.604000] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
  274. [    0.612000] TCP: Hash tables configured (established 131072 bind 65536)
  275. [    0.620000] TCP: reno registered
  276. [    0.620000] UDP hash table entries: 512 (order: 2, 16384 bytes)
  277. [    0.628000] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
  278. [    0.636000] NET: Registered protocol family 1
  279. [    0.640000] RPC: Registered named UNIX socket transport module.
  280. [    0.644000] RPC: Registered udp transport module.
  281. [    0.652000] RPC: Registered tcp transport module.
  282. [    0.656000] RPC: Registered tcp NFSv4.1 backchannel transport module.
  283. [    0.660000] Unpacking initramfs...
  284. [    0.840000] Initramfs unpacking failed: junk in compressed archive
  285. [    0.856000] Freeing initrd memory: 4096K
  286. [    0.860000] Disply Reset Status : On
  287. [    0.864000] Display LCD register operation
  288. [    0.868000] Display.0 fps=61 (16 ms), wait= 6 jiffies, Pixelclk=50000000hz
  289. [    0.876000] LCD : [1]=LCD connect to [5]=SYNCGEN0
  290. [    0.880000] audit: initializing netlink socket (disabled)
  291. [    0.884000] type=2000 audit(0.884:1): initialized
  292. [    0.892000] highmem bounce pool size: 64 pages
  293. [    0.904000] NFS: Registering the id_resolver key type
  294. [    0.908000] fuse init (API version 7.18)
  295. [    0.916000] msgmni has been set to 1089
  296. [    0.920000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
  297. [    0.928000] io scheduler noop registered
  298. [    0.932000] io scheduler deadline registered
  299. [    0.936000] io scheduler cfq registered (default)
  300. [    0.940000] display.0 connected to fb.0  ...
  301. [    0.944000] nxp-fb.0: dma addr = 0x63600000, buf[0xe32d6e80]
  302. [    0.952000] nxp-fb.0: dma addr = 0x63858000, buf[0xe32d7040]
  303. [    1.020000] nxp-fb 0: out[0], 1024 * 600 - 32 bpp (phys:63600000 virt:0xef831000 max:4915200)
  304. [    1.040000] Console: switching to colour frame buffer device 128x37
  305. [    1.064000] uart-pl011 uart-pl011.0: no DMA platform data
  306. [    1.068000] uart-pl011 uart-pl011.1: no DMA platform data
  307. [    1.076000] uart-pl011 uart-pl011.3: no DMA platform data
  308. [    1.080000] uart-pl011 uart-pl011.4: no DMA platform data
  309. [    1.088000] loop: module loaded
  310. [    1.092000] tun: Universal TUN/TAP device driver, 1.6
  311. [    1.100000] tun: (C) 1999-2004 Max Krasnyansky
  312. [    1.108000]  -- nxpmac initialize --
  313. [    1.116000] stmmac - user ID: 0x37, Synopsys ID: 0x37
  314. [    1.124000]  Ring mode enabled
  315. [    1.132000]  DMA HW capability register supported
  316. [    1.136000]  Enhanced/Alternate descriptors
  317. [    1.148000]  Enabled extended descriptors
  318. [    1.156000]  RX Checksum Offload Engine supported (type 2)
  319. [    1.164000]  TX Checksum insertion supported
  320. [    1.172000]  Wake-Up On Lan supported
  321. [    1.180000]  Enable RX Mitigation via HW Watchdog Timer
  322. [    1.236000] stmmac: probed
  323. [    1.240000] eth0: PHY ID 001cc915 at 0 IRQ 215 (stmmac-0:00)
  324. [    1.252000] eth0: PHY ID 001cc915 at 7 IRQ 215 (stmmac-0:07) active
  325. [    1.260000] PPP generic driver version 2.4.2
  326. [    1.268000] PPP BSD Compression module registered
  327. [    1.276000] PPP Deflate Compression module registered
  328. [    1.292000] PPP MPPE Compression module registered
  329. [    1.300000] NET: Registered protocol family 24
  330. [    1.308000] u***core: registered new interface driver asix
  331. [    1.320000] u***core: registered new interface driver cdc_ether
  332. [    1.328000] u***core: registered new interface driver net1080
  333. [    1.336000] u***core: registered new interface driver cdc_subset
  334. [    1.344000] u***core: registered new interface driver zaurus
  335. [    1.356000] u***core: registered new interface driver cdc_ncm
  336. [    1.364000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  337. [    1.372000] nxp-ehci nxp-ehci: SLsi Synopsys EHCI Host Controller
  338. [    1.384000] nxp-ehci nxp-ehci: new USB bus registered, assigned bus number 1
  339. [    1.392000] nxp-ehci nxp-ehci: irq 50, io mem 0xc0030000
  340. [    1.412000] nxp-ehci nxp-ehci: USB 0.0 started, EHCI 1.00
  341. [    1.420000] u*** u***1: New USB device found, idVendor=1d6b, idProduct=0002
  342. [    1.428000] u*** u***1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  343. [    1.440000] u*** u***1: Product: SLsi Synopsys EHCI Host Controller
  344. [    1.448000] u*** u***1: Manufacturer: Linux 3.4.39-s5p4418 ehci_hcd
  345. [    1.456000] u*** u***1: SerialNumber: nxp-ehci
  346. [    1.464000] hub 1-0:1.0: USB hub found
  347. [    1.472000] hub 1-0:1.0: 3 ports detected
  348. [    1.480000] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
  349. [    1.688000] Core Release: 2.93a
  350. [    1.696000] Setting default values for core params
  351. [    1.704000] Finished setting default values for core params
  352. [    1.792000] u*** 1-1: new high-speed USB device number 2 using nxp-ehci
  353. [    1.912000] Using Descriptor DMA mode
  354. [    1.920000] Dedicated Tx FIFOs mode
  355. [    1.928000] dwc_otg dwc_otg: DWC OTG Controller
  356. [    1.932000] u*** 1-1: New USB device found, idVendor=05e3, idProduct=0608
  357. [    1.932000] u*** 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
  358. [    1.932000] u*** 1-1: Product: USB2.0 Hub
  359. [    1.932000] hub 1-1:1.0: USB hub found
  360. [    1.932000] hub 1-1:1.0: 4 ports detected
  361. [    1.976000] dwc_otg dwc_otg: new USB bus registered, assigned bus number 2
  362. [    1.988000] dwc_otg dwc_otg: irq 49, io mem 0x00000000
  363. [    1.996000] u*** u***2: New USB device found, idVendor=1d6b, idProduct=0002
  364. [    2.004000] u*** u***2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  365. [    2.016000] u*** u***2: Product: DWC OTG Controller
  366. [    2.024000] u*** u***2: Manufacturer: Linux 3.4.39-s5p4418 dwc_otg_hcd
  367. [    2.036000] u*** u***2: SerialNumber: dwc_otg
  368. [    2.044000] hub 2-0:1.0: USB hub found
  369. [    2.052000] hub 2-0:1.0: 1 port detected
  370. [    2.056000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  371. [    2.068000] nxp-ohci nxp-ohci: SLsi Synopsys OHCI Host Controller
  372. [    2.076000] nxp-ohci nxp-ohci: new USB bus registered, assigned bus number 3
  373. [    2.088000] nxp-ohci nxp-ohci: irq 50, io mem 0xc0020000
  374. [    2.156000] u*** u***3: New USB device found, idVendor=1d6b, idProduct=0001
  375. [    2.164000] u*** u***3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  376. [    2.176000] u*** u***3: Product: SLsi Synopsys OHCI Host Controller
  377. [    2.184000] u*** u***3: Manufacturer: Linux 3.4.39-s5p4418 ohci_hcd
  378. [    2.196000] u*** u***3: SerialNumber: nxp-ohci
  379. [    2.204000] hub 3-0:1.0: USB hub found
  380. [    2.208000] u*** 1-1.2: new full-speed USB device number 3 using nxp-ehci
  381. [    2.224000] hub 3-0:1.0: 3 ports detected
  382. [    2.232000] Initializing USB Mass Storage driver...
  383. [    2.240000] u***core: registered new interface driver u***-storage
  384. [    2.248000] USB Mass Storage support registered.
  385. [    2.256000] u***core: registered new interface driver u***serial
  386. [    2.268000] u***core: registered new interface driver u***serial_generic
  387. [    2.276000] USB Serial support registered for generic
  388. [    2.308000] u*** 1-1.2: New USB device found, idVendor=1d57, idProduct=fa60
  389. [    2.320000] u*** 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
  390. [    2.332000] u*** 1-1.2: Product: 2.4G Receiver
  391. [    2.340000] u*** 1-1.2: Manufacturer: Compx
  392. [    2.348000] u***serial: USB Serial Driver core
  393. [    2.356000] u***core: registered new interface driver ftdi_sio
  394. [    2.368000] USB Serial support registered for FTDI USB Serial Device
  395. [    2.376000] ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver
  396. [    2.388000] u***core: registered new interface driver option
  397. [    2.396000] USB Serial support registered for GSM modem (1-port)
  398. [    2.408000] u***core: registered new interface driver pl2303
  399. [    2.416000] USB Serial support registered for pl2303
  400. [    2.424000] g_ether gadget: using random self ethernet address
  401. [    2.436000] u***0: MAC 16:01:aa:54:d3:f9
  402. [    2.444000] u***0: HOST MAC 82:cf:ce:fa:44:18
  403. [    2.452000] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
  404. [    2.464000] g_ether gadget: g_ether ready
  405. [    2.472000] mousedev: PS/2 mouse device common for all mice
  406. [    2.480000] input: Nexell Keypad as /devices/platform/nxp-keypad/input/input0
  407. [    2.492000] u***core: registered new interface driver xpad
  408. [    2.500000] Fail, arbit i2c.2  addr [0x8c] data[0x8d], trans[ 0: 1]
  409. [    2.512000] i2c.2 addr 0x8c (try:1)
  410. [    2.524000] IT7260-ts 2-0046: Found chip ITE726060
  411. [    2.532000] input: it7260_ts as /devices/virtual/input/input1
  412. [    2.540000] i2c-core: driver [IT7260-ts] using legacy suspend method
  413. [    2.552000] i2c-core: driver [IT7260-ts] using legacy resume method
  414. [    2.564000] touchscreen-1wire        initialized
  415. [    2.572000] backlight-1wire  initialized
  416. [    2.580000] input: fa_ts_input as /devices/virtual/input/input2
  417. [    2.588000] ts-if    initialized
  418. [    2.596000] [RTC] day=2016.01.01 time=08:28:36
  419. [    2.604000] nxp-rtc nxp-rtc.0: rtc core: registered nxp-rtc as rtc0
  420. [    2.616000] i2c /dev entries driver
  421. [    2.624000] lirc_dev: IR Remote Control driver registered, major 248
  422. [    2.636000] IR NEC protocol handler initialized
  423. [    2.644000] IR RC5(x) protocol handler initialized
  424. [    2.652000] IR RC6 protocol handler initialized
  425. [    2.660000] IR JVC protocol handler initialized
  426. [    2.668000] IR Sony protocol handler initialized
  427. [    2.676000] IR RC5 (streamzap) protocol handler initialized
  428. [    2.688000] IR SANYO protocol handler initialized
  429. [    2.696000] IR LIRC bridge handler initialized
  430. [    2.704000] gspca_main: v2.14.0 registered
  431. [    2.716000] ...................................ov5640_probe 2234
  432. [    2.728000] ...................................ov5640_video_probe 2193
  433. [    2.736000] Fail, noack i2c.0 addr [0x78] data[0x78], trans[ 0: 2]
  434. [    2.748000] i2c.0 addr 0x78 (try:1)
  435. [    2.756000] Fail, noack i2c.0 addr [0x78] data[0x78], trans[ 0: 2]
  436. [    2.764000] i2c.0 addr 0x78 (try:2)
  437. [    2.772000] Error: i2c.0, addr:78, trans len:-11(2), try:2
  438. [    2.780000] Fail, noack i2c.0 addr [0x78] data[0x78], trans[ 0: 2]
  439. [    2.792000] i2c.0 addr 0x78 (try:1)
  440. [    2.800000] Fail, noack i2c.0 addr [0x78] data[0x78], trans[ 0: 2]
  441. [    2.808000] i2c.0 addr 0x78 (try:2)
  442. [    2.816000] Error: i2c.0, addr:78, trans len:-11(2), try:2
  443. [    2.828000] Fail, noack i2c.0 addr [0x78] data[0x78], trans[ 0: 2]
  444. [    2.836000] i2c.0 addr 0x78 (try:1)
  445. [    2.844000] Fail, noack i2c.0 addr [0x78] data[0x78], trans[ 0: 2]
  446. [    2.852000] i2c.0 addr 0x78 (try:2)
  447. [    2.860000] Error: i2c.0, addr:78, trans len:-11(2), try:2
  448. [    2.872000] ov5640 0-003c: reg_read: i2c read error, reg: 300a
  449. [    2.880000] OV5640 read error!!!!!!!!!!!!!!!
  450. [    2.888000] ov5640_initialize_ctrls.............1794...........
  451. [    2.904000] u***core: registered new interface driver uvcvideo
  452. [    2.916000] USB Video Class driver (1.1.1)
  453. [    2.924000] Driver for 1-wire Dallas network protocol.
  454. [    2.932000] device-mapper: uevent: version 1.0.3
  455. [    2.940000] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com
  456. [    2.956000] DVFS: ASV[0] IDS(10mA,  8) Ro(110, 98)
  457. [    2.968000] DVFS: regulator vdd_arm_1.3V
  458. [    2.976000] DVFS: cpu DVFS with PLL.1 [tables=8]
  459. [    2.984000] cpuidle: using governor ladder
  460. [    2.992000] cpuidle: using governor menu
  461. [    3.000000] Synopsys Designware Multimedia Card Interface Driver
  462. [    3.008000] dw_mmc dw_mmc.0: Using internal DMA controller.
  463. [    3.020000] mmc0: no vmmc regulator found
  464. [    3.028000] dw_mmc dw_mmc.0: Using external card detect irq 225 (io 161)
  465. [    3.040000] dw_mmc dw_mmc.0: Version ID is 250a
  466. [    3.048000] dw_mmc dw_mmc.0: DW MMC controller at irq 43, 32 bit host data width, 32 deep fifo hw timeout 500 ms
  467. [    3.056000] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
  468. [    3.072000] input: Compx 2.4G Receiver as /devices/platform/nxp-ehci/u***1/1-1/1-1.2/1-1.2:1.0/input/input3
  469. [    3.088000] generic-u*** 0003:1D57:FA60.0001: input,hidraw0: USB HID v1.01 Keyboard [Compx 2.4G Receiver] on u***-nxp-ehci-1.2/input0
  470. [    3.104000] input: Compx 2.4G Receiver as /devices/platform/nxp-ehci/u***1/1-1/1-1.2/1-1.2:1.1/input/input4
  471. [    3.112000] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
  472. [    3.112000] mmc0: new high speed SDHC card at address 0001
  473. [    3.112000] mmcblk0: mmc0:0001 SD 7.43 GiB
  474. [    3.112000]  mmcblk0: p1 p2
  475. [    3.152000] generic-u*** 0003:1D57:FA60.0002: input,hidraw1: USB HID v1.01 Mouse [Compx 2.4G Receiver] on u***-nxp-ehci-1.2/input1
  476. [    3.192000] input: Compx 2.4G Receiver as /devices/platform/nxp-ehci/u***1/1-1/1-1.2/1-1.2:1.2/input/input5
  477. [    3.204000] generic-u*** 0003:1D57:FA60.0003: input,hidraw2: USB HID v1.01 Device [Compx 2.4G Receiver] on u***-nxp-ehci-1.2/input2
  478. [    3.220000] u***core: registered new interface driver u***hid
  479. [    3.228000] u***hid: USB HID core driver
  480. [    3.240000] ADC: CHs 8, 200000(1000000 ~ 130208) sample rate, polling mode, scale=166(bit 6)
  481. [    3.252000] snd pcm: register sound platform 'nxp-pcm'
  482. [    3.260000] snd i2s: ch 0, master, iis mode, 48000(47999)hz, 32 FBITs, MCLK=12287980hz, RFS=256
  483. [    3.388000] asoc: ES8316 HiFi <-> nxp-i2s.0 mapping ok
  484. [    3.408000] spdif-tx: 48000(47348)Hz, MCLK=12121212hz HDMI out
  485. [    3.416000] asoc: dit-hifi <-> nxp-spdif-tx mapping ok
  486. [    3.428000] GACT probability NOT on
  487. [    3.432000] Mirror/redirect action on
  488. [    3.440000] u32 classifier
  489. [    3.444000]     Actions configured
  490. [    3.452000] Netfilter messages via NETLINK v0.30.
  491. [    3.460000] nf_conntrack version 0.5.0 (12969 buckets, 51876 max)
  492. [    3.472000] ctnetlink v0.93: registering with nfnetlink.
  493. [    3.480000] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
  494. [    3.488000] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
  495. [    3.500000] xt_time: kernel timezone is -0000
  496. [    3.508000] ip_tables: (C) 2000-2006 Netfilter Core Team
  497. [    3.516000] arp_tables: (C) 2002 David S. Miller
  498. [    3.524000] TCP: cubic registered
  499. [    3.528000] Initializing XFRM netlink socket
  500. [    3.536000] NET: Registered protocol family 10
  501. [    3.544000] Mobile IPv6
  502. [    3.552000] ip6_tables: (C) 2000-2006 Netfilter Core Team
  503. [    3.560000] IPv6 over IPv4 tunneling driver
  504. [    3.568000] NET: Registered protocol family 17
  505. [    3.576000] NET: Registered protocol family 15
  506. [    3.584000] NET: Registered protocol family 35
  507. [    3.588000] Registering the dns_resolver key type
  508. [    3.596000] Registering SWP/SWPB emulation handler
  509. [    3.608000] axp22_dcdc5: incomplete constraints, leaving on
  510. [    3.616000] axp22_dcdc4: incomplete constraints, leaving on
  511. [    3.624000] axp22_dcdc3: incomplete constraints, leaving on
  512. [    3.636000] axp22_dcdc2: incomplete constraints, leaving on
  513. [    3.644000] axp22_dcdc1: incomplete constraints, leaving on
  514. [    3.652000] axp22_dc5ldo: incomplete constraints, leaving on
  515. [    3.660000] axp22_eldo2: incomplete constraints, leaving on
  516. [    3.668000] axp22_eldo1: incomplete constraints, leaving on
  517. [    3.680000] axp22_dldo1: incomplete constraints, leaving on
  518. [    3.688000] axp22_aldo3: incomplete constraints, leaving on
  519. [    3.696000] axp22_aldo2: incomplete constraints, leaving on
  520. [    3.704000] axp22_aldo1: incomplete constraints, leaving on
  521. [    3.712000] otg_wakelock_init: No USB transceiver found
  522. [    3.720000] nxp-rtc nxp-rtc.0: setting system clock to 2016-01-01 08:28:37 UTC (1451636917)
  523. [    3.732000] TMU: register adc.2 to hwmon
  524. [    3.736000] ALSA device list:
  525. [    3.740000]   #0: I2S-ES8316
  526. [    3.744000]   #1: SPDIF-Transciever
  527. [    3.752000] Freeing init memory: 220K
  528. [    3.756000] Write protecting the kernel text section c0008000 - c07b5000
  529. [    3.764000] rodata_test: attempting to write to read-only section:
  530. [    3.772000] write to read-only section trapped, success



` 152157e94sa6e9q4u4a966.png.thumb.jpg
已退回1积分

回帖（8）

jinyi7016

2016-5-22 10:37:02
是用的多大的卡啊，是送的那个卡么？
举报

DXK123~

2016-5-22 10:47:29
引用: jinyi7016 发表于 2016-5-22 10:37
是用的多大的卡啊，是送的那个卡么？

是的，用的就是人家送的那个卡
举报

jinyi7016

2016-5-22 10:53:35
引用: DXK123~ 发表于 2016-5-22 10:47
是的，用的就是人家送的那个卡

我用16G卡烧写时会出现这种情况，有自带的那个就没有问题了。
举报

andy4313

2016-5-22 14:31:43
刷debian系统看看呢
举报

更多回帖

8 0 0

相关问答

发帖
电子发烧友APP
|投诉反馈|电子发烧友网
© 2021 bbs.elecfans.com
湘ICP备2023018690号
×
20
完善资料，
赚取积分