这来自手动探头设置：RTD 2w，RTD 4w（默认），Thermis2w，Thermis4w，TCouple（仅限34465A / 70A）我已确认我的34461A在温度测量中没有TCouple探头设置。
所以简短的回答是否定的。这可能会在未来的固件升级中发生变化（请不要屏住呼吸）。
更长的答案是你可以使用你的探头，这个表[http://www.pyromation.com/Downloads/Data/emfk_c.pdf]并从你的探头中清除直流电压，查看表格中的温度，你就可以了
完成了。
K型探头在0C -V负温度下为0V，在正温度下为+ V（100C = 4.096mV和37C = 1.489mV）如果你被困在F温度范围内你可以使用这个表[http：//
www.pyromation.com/Downloads/Data/emfk_f.pdf] Johan-Fredrik更多表格？
试试这个[http://www.pyromation.com/Downloads/Data/temperature-tables.pdf]
以上来自于谷歌翻译
以下为原文
This is from the manual
Probe Settings: RTD 2w, RTD 4w (default), Thermis2w, Thermis4w, TCouple (34465A/70A only)
I have confirmed that my 34461A do not have the TCouple probe setting in temperature messurement.
So the short answer is no.This may change in a future firmware upgrade (please don't hold your breath).
The longer answer is that you can use your probe, this table [http://www.pyromation.com/Downloads/Data/emfk_c.pdf] and messuring the DC voltage from your probe, lookup the temp in the table and you'r done. The K type probe messures 0V at 0C -V at negative temperature and +V on positive temperature (100C = 4.096mV and 37C = 1.489mV)
If you are stuck in the F scale of temperature you can use this table [http://www.pyromation.com/Downloads/Data/emfk_f.pdf]
Johan-Fredrik
More tables ? Try this [http://www.pyromation.com/Downloads/Data/temperature-tables.pdf]
这来自手动探头设置：RTD 2w，RTD 4w（默认），Thermis2w，Thermis4w，TCouple（仅限34465A / 70A）我已确认我的34461A在温度测量中没有TCouple探头设置。
所以简短的回答是否定的。这可能会在未来的固件升级中发生变化（请不要屏住呼吸）。
更长的答案是你可以使用你的探头，这个表[http://www.pyromation.com/Downloads/Data/emfk_c.pdf]并从你的探头中清除直流电压，查看表格中的温度，你就可以了
完成了。
K型探头在0C -V负温度下为0V，在正温度下为+ V（100C = 4.096mV和37C = 1.489mV）如果你被困在F温度范围内你可以使用这个表[http：//
www.pyromation.com/Downloads/Data/emfk_f.pdf] Johan-Fredrik更多表格？
试试这个[http://www.pyromation.com/Downloads/Data/temperature-tables.pdf]
以上来自于谷歌翻译
以下为原文
This is from the manual
Probe Settings: RTD 2w, RTD 4w (default), Thermis2w, Thermis4w, TCouple (34465A/70A only)
I have confirmed that my 34461A do not have the TCouple probe setting in temperature messurement.
So the short answer is no.This may change in a future firmware upgrade (please don't hold your breath).
The longer answer is that you can use your probe, this table [http://www.pyromation.com/Downloads/Data/emfk_c.pdf] and messuring the DC voltage from your probe, lookup the temp in the table and you'r done. The K type probe messures 0V at 0C -V at negative temperature and +V on positive temperature (100C = 4.096mV and 37C = 1.489mV)
If you are stuck in the F scale of temperature you can use this table [http://www.pyromation.com/Downloads/Data/emfk_f.pdf]
Johan-Fredrik
More tables ? Try this [http://www.pyromation.com/Downloads/Data/temperature-tables.pdf]
举报
举报
